Dacor RO130B Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para não Dacor RO130B. Dacor RO130B Combined Configuration Drop-In Cooktop_RV_Single Wall Oven [fr] [ro] Manual do Utilizador

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
  • Página
    / 2
  • Índice
  • MARCADORES
  • Avaliado. / 5. Com base em avaliações de clientes
Vista de página 0
All specications subject to change without notice.
Phone: (800) 793-0093www.dacor.com
PLANNING
GUIDE
COMBINATION INSTALLATIONS
Drop-In Cooktop with RV Series
Downdraft Vent and Single Wall Oven
Document # PGCI-009
Revised 03/11/14 Page 1/2
Dacor DO, DYO, EO, EORS,
MOH, MORS, MOV, RO or ROV
series single wall oven
C
Support platform
3/4" (1.9 cm) min. thickness
1" min. (2.5 cm)
1/ 3/4” (4.4 cm)
for EO/MO
B
cooktop and vent cutout
RV30/36/46 with
remote or in-line blower
29 3/8" (74.6 cm) min.
* DYO series only: 1" min. (2.5 cm)
Adjustable support leg
Cabinet face
*
A
Minimum from
finished
countertop to
oven platform
Cooktop
Oven
Backsplash
Wall board
Wall
Downdraft vent
Dacor ETT, MET, RGC RNCT,
or SGM drop-in cooktop
Bottom exhaust
configuration shown
5/8" (1.6 cm) min.
countertop overhang
5/8" (1.6 cm) min. gap
behind downdraft vent to
allow for stiffner
Back of
cabinet interior
Stiffner
Finished floor
CUTAWAy SIDE VIEW
All tolerances: +1/16” (+1.6 mm), -0, unless otherwise stated
WARNING
• Observe all governing codes and ordinances during
planning and installation. Contact your local building
department for further information.
• All appliances must be installed in accordance with the
accompanying installation instructions.
COUNTERTOP CUTOUT - TOP VIEW
COUNTERTOP CUTOUT - ISO VIEW
5/8" min.
(1.6 cm)
Cabinet face
below countertop
Downdraft mounting
notch, required on some
configurations
E
C
B
D
F
Notches for
downdraft vent
not required with
some cooktops
See following pages for dimension table and compatible downdraft
vent models.
This configuration is not compatible with cabinet blower model
CABP3.
*
*
* When the cooktop chassis is about the same width as the
downdraft vent chassis, the cutout does not need to be notched
(cutout is rectangular). In cases were the cutout is rectangular,
dimension D on the following pages will be “NA” and dimension E
will be equal to dimension F.
Vista de página 0
1 2

Resumo do Conteúdo

Página 1 - COMBINATION INSTALLATIONS

All specications subject to change without notice.Phone: (800) 793-0093www.dacor.comPLANNINGGUIDECOMBINATION INSTALLATIONSDrop-In Cooktop with RV Ser

Página 2

All specications subject to change without notice.Phone: (800) 793-0093www.dacor.comPLANNINGGUIDECOMBINATION INSTALLATIONSDrop-In Cooktop with RV Ser

Comentários a estes Manuais

Sem comentários